_ALLOW_RESETLOGS_CORRUPTION 参数

联系:手机(13429648788)  QQ(107644445)

链接:https://www.orasos.com/_allow_resetlogs_corruption-%e5%8f%82%e6%95%b0.html

标题:_ALLOW_RESETLOGS_CORRUPTION 参数

作者:惜分飞©版权所有[文章允许转载,但必须以链接方式注明源地址,否则追究法律责任.]

我相信_ALLOW_RESETLOGS_CORRUPTION 这个参数一定很多人都熟悉,是redo异常恢复的杀手锏之一,以下文章是来自官方的解释

DB_Parameter _ALLOW_RESETLOGS_CORRUPTION 
========================================
 
This documentation has been prepared avoiding the mention of the complex 
structures from the code and to simply give an insight to the 'damage it could 
cause'.  The usage of this parameter leads to an in-consistent Database with no 
other alternative but to rebuild the complete Database.  This parameter could 
be used when we realize that there are no stardard options available and are 
convinced that the customer understands the implications of using the Oracle's 
secret parameter.  The factors to be considered are ;-- 
 
1. Customer does not have a good backup. 
2. A lot of time and money has been invested after the last good backup and     
   there is no possibility for reproduction of the lost data. 
3. The customer has to be ready to export the full database and import it     
   back after creating a new one. 
4. There is no 100% guarantee that by using this parameter the database would 
   come up. 
5. Oracle does not support the database after using this parameter for        
   recovery.    
6. ALL OPTIONS including the ones mentioned in the action part of the error   
   message have been tried. 
 
 

 
By setting _ALLOW_RESETLOGS_CORRUPTION=TRUE, certain consistency checks are 
SKIPPED during database open stage.  This basically means it does not check 
the datafile headers as to what the status was before the shutdown and how it 
was shutdown.  The following cases mention few of the checks that were skipped. 
 
Case-I 
------ 
Verification that the datafile present has not been restored from a BACKUP 
taken before the database was opened successfully by using RESETLOGS.   

ORA-01190: control file or data file %s is from before the last RESETLOGS
    Cause: Attempting to use a data file when the log reset information in  
           the file does not match the control file.  Either the data file or  
           the control file is a backup that was made before the most recent 
           ALTER DATABASE OPEN RESETLOGS. 
   Action: Restore file from a more recent backup. 

 
Case-II 
------- 
Verification that the status bit of the datafile is not in a FUZZY state. 
The datafile could be in this state due to the database going down when the  
 - Datafile was on-line and open 
 - Datafile was not closed cleanly (maybe due to OS). 

ORA-01194: file %s needs more recovery to be consistent 
    Cause: An incomplete recover session was started, but an insufficient 
           number of logs were applied to make the file consistent.  The  
           reported file was not closed cleanly when it was last opened by 
           the database.  It must be recovered to a time when it was not  
           being updated.  The most likely cause of this error is forgetting 
           to restore the file from a backup before doing incomplete  
           recovery. 
   Action: Either apply more logs until the file is consistent or restore the 
           file from an older backup and repeat recovery. 
 

Case-III 
-------- 
Verification that the COMPLETE recover strategies have been applied for 
recovering the datafile and not any of the INCOMPLETE recovery options.  
Basically because the complete recovery is one in which we even apply the 
ON-LINE redo log files and open the DB without reseting the logs. 

ORA-01113: file '%s' needs media recovery starting at log sequence # %s 
    Cause: An attempt was made to open a database file that is in need of  
           media recovery. 
   Action: First apply media recovery to the file. 

 
Case-IV 
------- 
Verification that the datafile has been recovered through an END BACKUP if the 
control file indicates that it was in backup mode. 
This is useful when the DB has crashed while in hot backup mode and we lost 
all log files in DB version's less than V7.2. 

ORA-01195: on-line backup of file %s needs more recovery to be consistent" 
    Cause: An incomplete recovery session was started, but an insufficient  
           number of logs were applied to make the file consistent.  The 
           reported file is an on-line backup which must be recovered to the 
           time the backup ended. 
   Action: Either apply more logs until the file is consistent or resotre 
          the database files from an older backup and repeat recovery. 
 
In version 7.2, we could simply issue the ALTER DATABASE DATAFILE xxxx END 
BACKUP statement and proceed with the recovery.  But again to issue this 
statement, we need to have the ON-LINE redo logs or else we still are forced to
use this parameter. 
 

Case-V 
------ 
Verification that the data file status is not still in (0x10) MEDIA recovery 
FUZZY. 
When recovery is started, a flag is set in the datafile header status flag to 
indicate that the file is presently in media recovery.  This is reset when 
recovery is completed and at times when it has not been reset we are forced to 
use this paramter. 

ORA-01196: file %s is inconsistent due to a failed media recovery session 
    Cause: The file was being recovered but the recovery did not terminate 
           normally.  This left the file in an inconsistent state.  No more  
           recovery was successfully completed on this file. 
   Action: Either apply more logs until the file is consistent or restore the 
           backup again and repeat recovery. 
 
 
Case-VI 
------- 
Verification that the datafile has been restored form a proper backup to 
correspond with the log files.  This situation could happen when we have 
decided that the data file is invalid since its SCN is ahead of the last 
applied logs SCN but it has not failed on one of the ABOVE CHECKS. 

ORA-01152: file '%s' was not restored from a sufficientluy old backup" 
    Cause: A manual recovery session was started, but an insufficient number 
           of logs were applied to make the database consistent.  This file is 
           still in the future of the last log applied.  Note that this  
           mistake can not always be caught. 
   Action: Either apply more logs until the database is consistent or 
           restore the database file from an older backup and repeat  
           recovery.

使用_ALLOW_RESETLOGS_CORRUPTION 参数需谨慎,因为该参数可能导致数据库逻辑不一致,甚至可能把本来很简单的一个恢复弄的非常复杂甚至不可恢复的后果,建议在oracle support支持下使用.另外使用该参数resetlogs库之后,强烈建议通过逻辑方式重建库